Expert Answers about Chevrolet Trailer Ramps
- Stallion Aluminum Car Hauler Ramp Set for Twin Axle Trailer
- The Stallion Aluminum Car Hauler Ramp Set item # 288-07502 you were looking at would be the perfect fit for your twin axle trailer. These ramps combined have a 6,000 lbs capacity and only weigh 20 lbs per ramp. They are 5' long x 14-1/2" wide x 3-3/4" thick and will work on a trailer up to 16" off the ground.
view full answer... - Can Gorilla-Lift Tailgate Lift Assist be Used on Folding Trailer Ramp
- The Gorilla-Lift Tailgate Lift Assist # GL1 could be used on a folding ramp. Yes, it should be attached to the first section of the ramp that is connected to the trailer. You could either fold the ramp and then lift or if your ramp allows you can use the lift assist to raise the entire ramp before folding.
view full answer... - Ramp Springs Needed To Turn A 75 Inch Ramp Into A Fold In Ramp
- When it comes to turning your ramp into a fold in ramp I would recommend 2 of The Spring # RS16933LH and 2 of The Spring # RS16933RH.
The spring is made out of a high quality steel alloy. The width of the spring is 3-3/4 inches and has an overall length of 10-1/2 inches.
I attached a review video link below.
view full answer... - Are There Trailer Ramps for Loading Cars That Keep Front End Up for Door Clearance
- We have options for loading ramps for a trailer to load up your vehicle, but none that are 10 inches or keep the front end up for door clearance when towing. Each of the available ramps hook onto the trailer and need to be removed after use; they are different lengths, widths, and capacities so you can get the one that will work for your vehicle.
- 72" Long x 14" Wide - 6,000 lbs: Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R72
- 84" Long x 14" Wide - 6,000 lbs: Gen-Y Hitch Aluminum...
view full answer... - Loading Ramp Recommendation for 2,100 lb Lift
- We do have a wide variety of loading ramp selections for you to choose from! I like the Aluminum Car Hauler Ramp Set - 60" x 14-1/2" - 6,000 lbs # 288-07502 because the aluminum construction makes them lightweight (20 lbs per ramp) and resistant to the elements so you don't have to worry about rust.
Attached is a review video of this ramp set for you to check out as well as our selection of loading ramps to filter through if you might want something else.
view full answer... - Are Ramp Door Hinges for Trailer Available?
- We do carry ramp door hinges though they are not made specifically for a Snowpro trailer. The ramp door hinge # PLR1902 is steel and gets welded on; I've added a photo showing the dimensions of this hinge as well as a link to a video review for you to take a look at and a link to our selection of hinges.
view full answer... - Availability of Lift Assist for Fold-Out Ramps on Gooseneck Trailer with Beaver Tail
- If your fold-out ramps connect to your beaver tail via a 1-1/2" diameter shaft then we have the 2K Ramp Springs # RS16933LH (left hand) and # RS16933RH (right hand) which you can install to help you raise and lower the ramps. Aside from this we wouldn't have anything to help with ramps specifically.
view full answer... - Longer Ramp Solution For The etrailer Motorcycle Carrier With Ramp
- The closest option I was able to locate is the Erickson Arched Loading Ramp Set # EM07435 which is a set of ramps that measures 9" wide, and 72" long.
Each ramp has a load limit of 500lbs, and when used in a pair has 1,000lbs capacity. When folded, this ramp measures 26-1/2" long, 9" wide, and 6" tall.
The 39-3/8" length ramp that the etrailer Motorcycle Carrier w/ Ramp for 2" Hitch # e98873 has is the longest ramp available for that motorcycle carrier.
view full answer... - Recommended Loading Ramp for a Honda Goldwing Trike Motorcycle
- The best option we have is to use the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R7 together with the Replacement Gen-Y Hitch 72" Aluminum Loading Ramp # GY96FR for a total of 3 ramps.
These ramps have a 3K capacity each, measure 72" long x 14" wide, and has sturdy hooked ends which will attach to your trailer deck.
view full answer... - Converting Barn Doors on an Enclosed Trailer to a Ramp
- We don't have the ramp itself but we have some parts that may work for you. We have hinges, like # SH300, for the ramp. I've linked our complete selection for you.
We also have latches that I've linked as well.
view full answer... - Replacement Ramp Door Spring Assembly for a Cargo Trailer Ramp Door
- The spring assemblies are pretty universal and can be cut to length depending on what size you need. The Conventional Ramp Door Spring for 7' Wide Enclosed Trailer - Dual Spring - 120-lb Capacity item # ERS120D81 will work for your Carry-On 6X12CGR7K. You will have to shorten the bar to get it down to the 66" wide you require. If you don't have experience working with torsion springs I recommend you contact a garage door installer. Each spring has to be wound a quarter turn at a time 30-40...
view full answer... - Recommended Ramps for Car Hauler Trailer
- Yes, I do believe we have something for you - check out the Gen-Y Hitch Aluminum Loading Ramp Set # GY52YR. This loading ramp measures 10' long, 15" wide (each ramp), and has a beefy 14,000 lb weight capacity so it'll be enough to load whatever you need.
view full answer... - Recommended 8 Foot Long Flat Ramps For Car Hauler Trailer
- I may have a solution for you, but we don't have the CargoSmart Arched Loading Ramp Set - Non-Folding - Aluminum - 90" x 12" - 3,000 lbs # 3483070 in a non-arched ramp. The only available flat ramp we have in close to 90" is the Gen-Y Hitch Aluminum Loading Ramp Set - 96" Long x 15" Wide - 10,000 lbs # 325-GH-R96. These are a heavy duty ramp set that is well rated for your race car and comes in an 8 foot long x 15" wide ramp section.
I've linked a review video of these ramps for you to...
view full answer... - Will a Leaf Spring Work on a 2 Horse Trailer With a Slant Ramp
- You were right on the money thinking that the 4-Leaf Double-Eye Spring # e54SR should work with your slant ramp on your 1989 Aluminum Classic Trailer.
Through some research, I was able to find out that Redline supplies many of the ramp springs to horse trailer manufacturers. The key point to make sure these are the correct ones is to measure the ones you currently have - I realize they are broken, but, do the best you can. You need to measure from center of one eye to the center of the...
view full answer... - How to Choose Best Thickness for Ramp Door Seal Kit
- If you already have a seal that you're replacing then you want to get a seal that's a similar size, otherwise if it's a brand new application then I recommend trying to find the depth of the gap and choosing a seal slightly taller since it will compress as you close the door.
For example, the Ramp Gate Seal Kit for Enclosed Trailer Ramp # SR55FR measures 1" tall so a gap of about 7/8" would be perfect for this application.
view full answer... - Lift Assist To Swing Up Ramp Door On 6 X 12 Cargo Trailer
- Though we would not have a hinge that would swing the door in the up position you could use The Gorilla-Lift Utility Trailer Tailgate Lift Assist w/ Cable # GL1.
This lift assist will allow you to easily lift and lower the ramp on your cargo trailer. It has durable stainless steel cables and has a weight capacity of 300 pounds. It has a fast, easy installation with included hardware.
I attached a review video link below.
view full answer... - What Bike Rack with Ramp do You Recommend for My 2013 Audi Q5?
- I have a great ramp solution for you. Unfortunately, the Swagman Current # S64678 does not have a compatible ramp that fits. It will, however, fit with the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75940 when installed on your 2013 Audi Q5.
With that being said, if you are looking for a ramp solution, a great alternative is the Yakima OnRamp - 2" Hitches # Y36FR. In addition to the integrated ramp, another advantage you receive with the OnRamp is the independently-adjustable...
view full answer... - What Bike ramp Can I Use for the Thule T2 Pro XTR # TH83JV?
- I have an answer for you. Unfortunately, we currently don't carry any bike ramps that are designed for your Thule T2 Pro XTR # TH83JV. The only thing that would come close would be to purchase something like the Race Ramps Trailer Loading Assist Ramps - 8" Lift - 74" Long - Qty 2 # RR-TR-8XL to use with your current rack.
With that being said, if you are open to purchasing another rack, we do have a great rack that has a built-in ramp. For this route, I recommend the Yakima OnRamp # Y36FR....
view full answer... - Are There Left and Right Hand Trailer Ramp Springs Available
- We do have the right hand along with the left hand trailer ramp springs available, which are the following:
- Right Hand: Ramp Spring - 2K Torque for 1-1/2" Shaft - RH # RS16933RH
- Left Hand: Ramp Spring - 2K Torque for 1-1/2" Shaft - LH # RS16933LH
I have added a link below to a video review for you to check out as well if you'd like.
view full answer... - Recommended Loading Ramps for Track Machine onto Trailer with Deck 4 Feet Off the Ground
- I have a solution for you, but because of the 4 foot loading height, you're going to need a ramp with some considerable length to it so that you can safely load this track machine. I recommend using the Gen-Y Hitch Aluminum Loading Ramps- 144" long # GH54FR, which will provide you with enough ramp length to load and unload this machine. Gen-Y prides themselves on the durability of their parts, so you're getting a heavy duty ramp set that should withstand some of the most difficult conditions.
view full answer...
Go To Results